型线、铝合金拉丝工艺1.docx

《型线、铝合金拉丝工艺1.docx》由会员分享，可在线阅读，更多相关《型线、铝合金拉丝工艺1.docx（2页珍藏版）》请在第一文库网上搜索。

1、广东远光电缆实业有限公司拉丝工艺卡型号1Y9编号M/YG3.12-2010共2页适用机台铝合金异型线大拉机组代替-第1页品种编号铝单线直径拉线工艺参数进线mm拉线轮序号模具位置和模具内径最高线速m/s标称直径直径偏差固定无级可调1234123456712.85+0.01-0.029.58.827.867.006.205.304.554.013.623.242.871622.93+0.01-0.029.58.827.867.006.205.304.554.013.623.242.951532.98+0.01-0.029.58.827.867.006.205.304.744.243.823.423

2、.001643.00+0.01-0.029.58.827.867.006.205.304.744.243.823.423.021653.07+0.02-0.039.58.827.867.006.205.304.744.243.823.423.091563.15+0.02-0.039.58.827.867.006.205.304.554.013.623.171473.20+0.02-0.039.58.827.867.006.205.304.554.013.623.221383.22+0.02-0.039.58.827.867.006.205.304.554.013.623.241393.33+0

3、.02-0.039.58.827.867.006.205.304.744.243.823.3513103.42+0.02-0.039.58.827.867.006.205.304.744.243.823.4412113.51+0.02-0.039.58.827.867.006.205.304.554.013.5311123.60+0.02-0.039.58.827.867.006.205.304.554.013.6211133.66+0.02-0.039.58.827.867.006.205.304.744.143.6810143.69+0.02-0.039.58.827.867.006.20

4、5.3C4.74.143.7110设计（日期）审核（日期）标准化（日期）会签（日期）审定（日期）批准（日期）于亚辉郑建凯王勋赵晓宏蒋陆肆蒋陆肆标记处数更改文件号签字日期标记处数更改文件号签字日期注：1画“一”表示该位置需要用模孔直径比前一道大12mm的模具，防止拉线时铝线抖动;2.操作台里面的工艺数据未经技术部允许，任何人不得改动。广东远光电缆实业有限公司拉丝工艺卡型号1Y9编号M/YG3.12-2010共2页适用机台铝合金异型线大拉机组代替-第2页品种编号铝单线直径拉线工艺参数进线mm拉线轮序号模具位置和模具内径最高线速m/s标称直径直径偏差固定无级可调12341234567153.76+0

5、.02-0.039.58.827.867.006.205.304.744.243.7810163.80+0.02-0.039.58.827.867.006.205.304.744.243.8210173.99+0.02-0.039.58.827.867.006.205.304.554.019184.12+0.02-0.039.58.827.867.006.205.304.744.148194.16+0.02-0.039.58.827.867.006.205.304.744.188204.20+0.02-0.039.58.827.867.006.205.304.744.228214.21+0.0

6、2-0.039.58.827.867.006.205.304.744.238224.22+0.02-0.039.58.827.867.006.205.304.744.248234.35+0.02-0.049.58.827.867.006.205.304.744.377244.42+0.02-0.049.58.827.867.006.205.304.744.447254.53+0.02-0.049.58.827.867.006.205.304.557264.63+0.02-0.049.58.827.867.006.205.304.656274.67+0.02-0.049.58.827.867.006.205.304.696284.72+0.02-0.049.58.827.867.006.205.3C4.746设计（日期）审核（日期）标准化（日期）会签（日期）审定（日期）批准（日期）于亚辉郑建凯王勋赵晓宏蒋陆肆蒋陆肆标记处数更改文件号签字日期标记处数更改文件号签字日期注：1画“一”表示该位置需要用模孔直径比前一道大12mm的模具，防止拉线时铝线抖动;2.操作台里面的工艺数据未经技术部允许，任何人不得改动。