友佳机床断刀检测设备方案书.docx

《友佳机床断刀检测设备方案书.docx》由会员分享，可在线阅读，更多相关《友佳机床断刀检测设备方案书.docx（25页珍藏版）》请在第一文库网上搜索。

1、VMP-23A友佳立式加工中心断刀检测系统机床品牌：友佳机床型号：VMP-23A操作系统：法兰克刀库形式：盘式刀库L断刀检测系统项目产品名称及型号单位数单价金额备注1PCS-100 断刀检测系统套1品牌：PMT日本合计货期2-3周建议型号PCS-100断刀检测系统包含：控制单元线缆（可选）探头探针具体参数PCS-100断刀检测器破损检测器破损检测系统：/夕夕卜iz：/廿一 PCS-100 (-Contact Sensor PCS-100 with Needle Assembly bn-Jb3.-/b(SCU-l 00)Control Unit (SCU-100)Z.-K/UR 140mmHa

2、200mm (口：/夕彳needle tength 140mm (STD) 200mm (Long type)用力 一Clamping CollarNeedle Assembly7-77K （平）二一卜儿（才 a （110mm 是、3mm 幅、0.5mm 厚）140mm(fl!率)Rat Wand (Option)110mm(L).3mm(W).0.5mm (T)Needle Cap丸棒二一21/ (1.3m(n)(脱落可) Std. Round NeedleV Cup Seal(Removable)接统勺一:/及(楝辜5m)Connecting Cable (STD : 5m) 55.0 m

3、meeeeeeeeOOLDOS10mm. 40mm64mm27.0mm7*夕夕90PURZ油夕彳 7Connecwr L90 or Stralfihx PUR cable5.0bBES3SB0BCE/一入可Long C8blc(l Om) available彼那=未夕夕一部 一体情造 Uni-xxly Design for Uhimate Sealing二一卜儿旋回角度调整Adjust Ring for Swing Angle彳卜口用tz，：/卜jfUl/卜Set Bolt5/7卜夕1/夕卜显劲式-(474(Shaft-Direct Drive (Without Gear Box)V力(脱着可

4、)V Cup Seal二一/fey bZi7Ua-lcrl取付I，取外L )Needle Cap(To be mounted or removedby tne set screw)140mm口才二一 KJb ： 200mm(200mmMAX.)Needle LengthStd. ： 140mmLong Needle : 200mm (Max.)才品7 V/卜(平)二一同 1/(全晟】10mm 幅3mm)二一户4/中共用Flat Wand (Option)110mm(L) 3mm (W)二一户儿先端部超硬表面处理(HRC85-90)Carbide depositted Uni-body Desi

5、gn for Ultimate Sealing一体成型机身工艺，高密封设计 Shaft-Direct Drive (Without Gear Box)轴直接驱动式，不带齿轮箱 Set Bolt固定螺栓 Adjust Ring for Swing Angle旋角调整环 V Cup SealV型密封 Needle Cap (To be mounted or removed by the set screw)针帽，可通过固定螺丝进行装卸 Needle Length Std: 140mm Long Needle: 200mm Max.探针长度，标准：140mm,最大：200mm Flat Wand (

6、Option) 110mm (L) 3mm (W)防护杆(选装)，长110mm,宽3mm Carbide deposited针表面超硬化处理探针摆动摆动角度5175。电机驱动直接驱动式直流电机工作电压直流24V最大电流250mA运行温度O-55C01. Contact Sensor PCS-100 with Needle Assembly接触式传感器/探头PCS-100以及探针配套装置Contact sensor PCS-100 Rotation angle can be set and/or changed flexibly CW or CCW, in the range of 5 to17

7、5.可通过设置或者更改旋转方向来调整旋转角度，调整范围为5。到175。.Setting CW or CCW on the control unit depends on where the sensor/needle is set, andwhich one could achieve the nearest contact to the tool.在控制器上操作，并据传感器探针的位置和就近被测工具的原则来调整旋转方向 Contact pressure of needle (speed of needle swing) can be changed in 3 steps by theswitc

8、h of control unit. The lowest swing speed is ideal for the small dia. of tools. Up toabout 0.4mm dia. of tools can be detected.只需要三步即可在控制器上调整探针的接触压力(探针旋转速度)，最低旋转速度适合测小尺寸的被测工具，最小测量工具尺寸为0.4mm。 Swing speed of the needle can be selected in several steps. It can help to minimize thecycle time of machinin

9、g.探针旋转速度只需要遵循几个步骤操作即可进行选择，这样能有效地缩短机器加工周期2. Control Unit SCU-100SCU-100控制单元OK outputIf a tool is detected, OK relay outputs a momentary or latch signal. Green LED illuminates.当被测件被检测到良好，继电输出一个瞬间信号，绿LED灯亮起。FAULT outputWhen a broken tool condition is detected, FAULT relay outputs a momentary or latch s

10、ignalRed LED illuminates.当检测到破损件时，瞬间发出一个故障信号，红色LED灯亮起System FaultA system Fault signal outputs at Fault relay when在以下情况会发出系统故障信号： The sensor malfunction.传感器故障 The sensor direction setting and the CW/CCW switch setting are opposite.传感器方向设置和正反旋转方向转换设置错反 There is a short or disconnection at the sensor

11、cable传感器电缆线短路后者断开Both Red and Green LED illuminate此时红绿灯同时亮起3. Connecting Cable (STD: 5m) with L90 Connector配有L90接头的电缆线，标准长5m4. Clamping Collar夹圈Housing外壳Anodized Aluminum阳极电镀铝Needle swing探针摆动Swing Angle 5-175mechanically adjustable摆动角度5175。，机械可调Needle探针Max Life needle in standard length 140mm, Long

12、needle 200 mm(Heat-Treated)标准长140mm,最长200mm (热处理)Motor drive电机驱动Direct Drive (No Gear Box) DC motor直接驱动式直流电机，不济齿轮箱Sealing密封Sealed against liquid and solid contaminants. Rating IP-67高密封，防止液体和固体污染侵蚀，防护等级达IP67Cable电缆90or straight, moulded 4 pin connector. Standard length 5M (Max.50M)垂直或者水平电缆线，带4针接头，标准长

13、5m,最大长为50mSCU-100 Control UnitSCU-100控制单元Operating voltage工作电压24VDC直流24VMax. current最大电流250mAOperating Temp.运行温度0-55C0Housing Material外壳材质Polycarbonate聚碳酸脂Max. wire size最大线规12AWGMounting安装方式35mm DIN Rail35mm导轨，符合德国工业标准OK Fault relay正常/故障信号继电输出Dry Contact (Contact Rating)干接触(接点容量)Additional Functions

14、附件功能Changeable to reverse logic for space monitoring空间监测时，逆向理论信号切换2 .激光对刀设备型号价格品牌NC4非接触式对刀系统48000Renishaw服务费用根据客户地址安装时间确认，安装，调试，差旅Renishaw此产品包含支架测头尺寸单位mm030口026 kA =安装孔(x2), M3 x 0.5 P x 8 mm深B =定位孔(x2). 02 mm x 8 mm深c =气动快接接头.03 mm望料管D=电源电缆06 mmE = PassivoSeal气密封孔.请勿盖住.测头状态LED指示灯(在发射器和接收器装置上)F =堵塞螺钉。请勿干扰。线缆：可根据机床型号来选目前